File Download

There are no files associated with this item.

  Links for fulltext
     (May Require Subscription)
Supplementary

Conference Paper: Effect of fabrication processes on bulk heterojunctions (BHJ) photovoltaic device performance

TitleEffect of fabrication processes on bulk heterojunctions (BHJ) photovoltaic device performance
Authors
KeywordsBulk heterojunction
OPVs
Platinum(II) metallopolyyne polymer
Issue Date2009
PublisherS P I E - International Society for Optical Engineering. The Journal's web site is located at http://spie.org/x1848.xml
Citation
Proceedings Of Spie - The International Society For Optical Engineering, 2009, v. 7416 How to Cite?
AbstractOrganic photovoltaic (OPV) devices have attracted much interest in recent decades because they have a great potential for low cost solar cells. Among different kinds of organic solar cells, conjugated polymer/fullerene bulk heterojunction (BHJ) solar cells have exhibited improvements in the power conversion efficiency (PCE) in recent years. The performance of BHJ solar cells is highly dependent on different fabrication processes. To address this issue, we focus on the dependence of different photovoltaic parameters on the fabrication methods. BHJ solar cells fabricated using platinum metallopolyyne (P1) with a low band gap of 1.85 eV as an electron donor and phenyl-C61-butyric acid methyl ester (PCBM) as an electron acceptor have been studied. The fabrication parameters, such as ratios of P1 to PCBM, solvents used, thickness of the active layers and top contact materials, have been systematically investigated. Blend ratio and solvent used had most significant influence on photovoltaic performance with several times higher efficiency of the best condition compared to the worst condition. They affected all photovoltaic parameters [open circuit voltage (V oc), short circuit current density (J sc) and the fill factor (FF)]. Top contact materials affected the V oc and the FF, while thickness of the active layer mainly affected the J sc and FF. The influence of different fabrication conditions on photovoltaic performance has been discussed. © 2009 SPIE.
Persistent Identifierhttp://hdl.handle.net/10722/176202
ISSN
2023 SCImago Journal Rankings: 0.152
ISI Accession Number ID
References

 

DC FieldValueLanguage
dc.contributor.authorCheung, KYen_HK
dc.contributor.authorYip, CTen_HK
dc.contributor.authorFung, MKen_HK
dc.contributor.authorDjurišić, ABen_HK
dc.contributor.authorChan, WKen_HK
dc.contributor.authorHe, Zen_HK
dc.contributor.authorWang, XZen_HK
dc.contributor.authorHo, CLen_HK
dc.contributor.authorWong, WYen_HK
dc.date.accessioned2012-11-26T09:06:50Z-
dc.date.available2012-11-26T09:06:50Z-
dc.date.issued2009en_HK
dc.identifier.citationProceedings Of Spie - The International Society For Optical Engineering, 2009, v. 7416en_US
dc.identifier.issn0277-786Xen_HK
dc.identifier.urihttp://hdl.handle.net/10722/176202-
dc.description.abstractOrganic photovoltaic (OPV) devices have attracted much interest in recent decades because they have a great potential for low cost solar cells. Among different kinds of organic solar cells, conjugated polymer/fullerene bulk heterojunction (BHJ) solar cells have exhibited improvements in the power conversion efficiency (PCE) in recent years. The performance of BHJ solar cells is highly dependent on different fabrication processes. To address this issue, we focus on the dependence of different photovoltaic parameters on the fabrication methods. BHJ solar cells fabricated using platinum metallopolyyne (P1) with a low band gap of 1.85 eV as an electron donor and phenyl-C61-butyric acid methyl ester (PCBM) as an electron acceptor have been studied. The fabrication parameters, such as ratios of P1 to PCBM, solvents used, thickness of the active layers and top contact materials, have been systematically investigated. Blend ratio and solvent used had most significant influence on photovoltaic performance with several times higher efficiency of the best condition compared to the worst condition. They affected all photovoltaic parameters [open circuit voltage (V oc), short circuit current density (J sc) and the fill factor (FF)]. Top contact materials affected the V oc and the FF, while thickness of the active layer mainly affected the J sc and FF. The influence of different fabrication conditions on photovoltaic performance has been discussed. © 2009 SPIE.en_HK
dc.languageengen_US
dc.publisherS P I E - International Society for Optical Engineering. The Journal's web site is located at http://spie.org/x1848.xmlen_HK
dc.relation.ispartofProceedings of SPIE - The International Society for Optical Engineeringen_HK
dc.subjectBulk heterojunctionen_HK
dc.subjectOPVsen_HK
dc.subjectPlatinum(II) metallopolyyne polymeren_HK
dc.titleEffect of fabrication processes on bulk heterojunctions (BHJ) photovoltaic device performanceen_HK
dc.typeConference_Paperen_HK
dc.identifier.emailDjurišić, AB: dalek@hku.hken_HK
dc.identifier.emailHo, CL: lamlamho@HKUCC-COM.hku.hken_HK
dc.identifier.authorityDjurišić, AB=rp00690en_HK
dc.identifier.authorityHo, CL=rp00704en_HK
dc.description.naturelink_to_subscribed_fulltexten_US
dc.identifier.doi10.1117/12.825062en_HK
dc.identifier.scopuseid_2-s2.0-70449588900en_HK
dc.relation.referenceshttp://www.scopus.com/mlt/select.url?eid=2-s2.0-70449588900&selection=ref&src=s&origin=recordpageen_HK
dc.identifier.volume7416en_HK
dc.identifier.isiWOS:000307649100015-
dc.publisher.placeUnited Statesen_HK
dc.identifier.scopusauthoridCheung, KY=25229974800en_HK
dc.identifier.scopusauthoridYip, CT=14043063100en_HK
dc.identifier.scopusauthoridFung, MK=35191896100en_HK
dc.identifier.scopusauthoridDjurišić, AB=7004904830en_HK
dc.identifier.scopusauthoridChan, WK=55152945600en_HK
dc.identifier.scopusauthoridHe, Z=36547970300en_HK
dc.identifier.scopusauthoridWang, XZ=8907969400en_HK
dc.identifier.scopusauthoridHo, CL=10242268200en_HK
dc.identifier.scopusauthoridWong, WY=7403972153en_HK
dc.identifier.issnl0277-786X-

Export via OAI-PMH Interface in XML Formats


OR


Export to Other Non-XML Formats